How to solve message "scanner unit is open" or "close the scanner unit" on Epson printers

tháng 4 28, 2016 Epson, Error code No comments

Solution 1:

Power off the printer
Unplug the power cord and wait 5 minutes
Plug back et power on

Solution 2: When you close the scanner assembly it pushes a small lever that say the scanner is closed. But sometimes, this lever is not pushed far enough, or is defective. Try this:

Close the scanner unit and slammed it slightly.
If it does not work, try to push the lever with a pencil

Printer Epson FX-890, FX-890A

tháng 4 27, 2016 Epson FX No comments

Téléchargements:

Drivers and manuals

Consommables:

C13S015329: Ribbon black

Accessories:

C12C814022: 50 Sheet A4 Sheet Feeder
C12C824432: Type B Serial Interface 20ma 0K
C12C811141: Epson Roll Paper Holder LX-300+II, LQ-580, LQ-680, FX-8, FX-890
C12C806382: High Capacity Cut Sheet Feeder (150 Copies) LQ-590, FX-890, FX-890A
C12C806372: Epson Standard Cut Sheet Feeder LQ-570+, LQ-870, LX-300+II, LQ-300+II
C12C800202: Tractor LQ-870, FX-870, FX-880, FX-890, LQ-5
C12C824352: EpsonNet 10 / 100 Base Tx.print serv.5e
C12C814011: Guide papier

Parts:

1274547: Ribbon mask
1259448, 1010896: Holder ribbon mask
2080699, 1499642, 1569488, 1596132: Power Supply PCB
1262597, 1598047: Housing Assy Panel
1267438, 1275824: Printhead
274270, 1254860: Paper eject assy
1408788, 1254859: Tractor assy
1236544: Sheet panel-B
1234467: Ribbon drive assy
2019011, 2071496: DETECTOR,PE,FRONT,S
1234171: Platen Knob
1234668 - Platen Assy - Large Roller in Middle of Printer
1004929 - Spur Gear 11.5
1235581 - 1005244 - Spur Gear 15
1005224 - Spur Gear 27
1005226 - Spur Gear 34
1013093 - Spur Gear 34.5
1031612 - Platten Spur Gear 36
1031702 - Gear Pin - Goes with 1031612 on FX/LQ2170
1031612 - 1025295 - 1044973 - 1073599 - 1032488 - 1032489 - Spur Gear 20
1232297 - Right Bushing 8
1232304: Epson Carriage Sub Assembly
1005727 - 2018904: Rear Paper Entry Detector Sensor Assembly
1008716: Combination Gear
1025296 - Paper Support

Troubleshooting:

Meaning of panel light:

Paper Out

Pause

Tear Off/Bin

Pitch

Font
long series of beeps (5 beeps)
An unknown printer error has occurred. Turn off the printer and leave it off for several minutes; then turn on the printer again. If the error recurs, contact your dealer.

Pause
(no bip)
The print head is overheated. Wait for a few minutes; the printer resumes printing automatically once the print head cools.

Paper Out

Pause
short series of beeps (3 beeps)
A single sheet of paper is not fully ejected. Press the Load/Eject button to eject the sheet.
or
Continuous paper is not fed to the standby position.
Tear off the printed page at the perforation; then press the Load/ Eject button. The printer feeds the paper to the standby position.
or
Paper is jammed in the printer. Clear the paper jam

Pause
short series of beeps (3 beeps)
The paper release lever is set to the wrong position.
Set the paper release lever to the position for the paper source you want to use.

Paper Out

Pause
short series of beeps (3 beeps)
No paper is loaded in the selected paper source.
Load paper in the printer or select a different paper source; the Paper Out light goes off. Then press the Pause button; the Pause light goes off and the printer starts printing.
or
The paper is not loaded correctly. Remove your paper and reload it correctly