Error Code list on some printers Canon Pixma

• E2-2 No paper (ASF)
• E3-3 Paper jam
• E4 No ink
• E5-5 The ink cartridges are not installed or a non-supported ink cartridge is installed, or the ink cartridges are not installed properly
• E8 Waste ink absorber full, or platen waste ink absorber full
• E9 The connected digital camera / video camera does not support Camera Direct Printing
• E14 The Ink cartridges whose destination are wrong
• E15 Ink cartridge is not installed E16 - Ink remaining is unknown
• E16 -E19 Failed to scan head alignment sheet
• E22 Carriage error
• E23 Paper feed error
• E24 Purge unit error
• E25 ASF(cam) sensor error
• E26 Internal temperature rise error
• E27 Waste ink absorber full or platen waste ink absorber full
• E28 Ink cartridge temperature rise error -
• E29 EEPROM error
• E33 Paper feed position error
• E35 15 USB Host VBUD overcurrent error - USB
• E37 17 Abnormal motor driver error
• E40 20 Other hardware error
• E42 22 Scanner error

Read More

Solving Error E3 on Canon Printers

Error E3 is a jam error.

Solution 1:

• Power on the printer.
• Open the door for a few seconds and do a print job.

Solution 2:

• Check for any piece of paper in the printer.
• After checking, install the paper and push the "Black" or "Color" Button.

Solution 3:

• Take a sheet of normal paper A4. fold it in two and still in two.
• Power off the printer.
• Insert the folded paper behind the printer.
• Power on the printer. If there is a foreign object, it will be extrated by the folded paper.

Solution 4:

• Push the red button during 5 seconds.

Read More

Solving "general error" on Epson printers

Some lights flash on the printer with this message.


Solution 1:

• Verify that the door is closed.

Solution 2:

• Look inside the printer that there is no sheet of paper or tiny object.

Solution 3: try a reset:

• SSC utility for some printers

Or (Epson Stylus Color series: 740, 760, 880...)

• Power off the printer.
• Remove the power cable during 1 minute and reconnect it on the printer.
• Hold on "Paper" et "Ink" button and "Power" button.
• When "Paper" button flash, release all buttons.
• Press "Ink" button until lights flah several times, then release.
• The printer begin a reset and a printhead cleaning.
• Power off and on.

Or (Epson R300...)

• Press and hold 'stop' 'maintenance' and 'power' buttons for about 10 seconds. A message will appear on the screen. 
• power off and back on for reset

Read More

Canon Pixma MP495 printer

MAJ15/12/16

Downloads:

• Drivers, Software, Manuels

Cartridges:

• PG-210: Black Ink
• PG210XL: Back ink XL
• CL-211: Color ink
• CL211XL: Colour Ink XL

Troubleshooting:

• Waste ink counter Reset (error E08):

Service tool V3400 for resetting Canon printers counter

• Ink cartridge reset (ship reset):

Solution 1 : When "empty cartridge" is displayed, Hold on the "cancel" button until "processing"appears.
Solution 2: Hold on the "Stop" button until "processing" appears

• Error E16 or E,1,6:

Hold on the "Stop" button for 5 seconds.

Read More

HP LaserJet M5035, M5035x, M5035xs Multifunction Printer

Downloads:

• Drivres and software
• Software Technical Reference (external)
• Using The Control Panel
• HP LaserJet M5025/M5035 MFP - (mulitple language) Getting Started Guide
• HP LaserJet M5035x/M5035xs MFP - (multiple language) Getting Started Guide 
• HP LaserJet M5035x/M5035xs MFP - (multiple language) Getting Started Guide 

Troubleshooting:

• HP LaserJet M5025 and M5035 MFP Series - Problem Solving Checklist
• HP LaserJet M5025 and M5035 MFP Series - Solve General Printing Issues
• Error 49.4C0:

Solution 1: First step is to restart the printer, clear all jobs with the Stop button, restart printer again.

Solution 2: Upgrade the firmware.

Solution 3:  If the message persists; Turn the MFP off. Remove the DIMM.
Remove any installed EIO devices. Turn the device on. If the error message disappears, reinstall the DIMM and EIO devices individually, making sure to turn the device power off and then on again as you install each device. Replace the component that caused the error message.

Read More

Printer Epson Stylus Photo R230, R230X

Links:

• Drivers and utilities

Troubleshooting:

• Waste ink full error (Service required):

- Download SCC Service Utiliy: http://www.ssclg.com/epsone.shtml
- Printer must be connected with the computer
- Install SSC Service Utility and run the program
- Choose Epson Stylus Photo R230 in setting configuration and close window.
- At the bottom right taskbar clik right icon SSC Utility.
- Choose Protection Counter / Reset Protection Counter / Clik Yes for the question “Have you Replace waste ink pad”.
- Restart the printer.

Read More

Error message "scan unit open or paper jam 2" on Samsung printers

This error could appears on Samsung CLX-2160, CLX-3175, CLX-3185, ...



Solution 1:

• Open and close the front cover. The jammed paper is automatically ejected from the machine. 
• Gently pull the paper out of the output tray. If there is no jammed paper or if there is any resistance when you pull, stop and go to the next step. 
• Lift the scan unit. 
• Holding the inner cover open, carefully take the jammed paper out of the machine. 
• Lowering down the scan unit gently and slowly until it is completely closed. The inner cover will be closed automatically by the scan unit closed. Be careful not to pinch your fingers! If there is any resistance and the paper does not move when you pull or if you cannot see the paper under the scan unit, continue to the next step. 
• Open the rear cover. 
• If you see the jammed paper, pull it straight up. 
• Close the rear cover. 
• Printing automatically resumes. 

Solution 2:

• If there is no debris or other foreign object in a sensor, it could still be something to small for you to see. 
• Try blowing out all those areas with a can of compressed air. 

Solution 3:

• Make sure the sensors are not just "stuck" in the wrong position. Sensors are spring-loaded and so should pop back to the detent position when pushed the opposite direction with a small pencil or ice pick. 

Solution 4:

• Verify that the scan unit (or automatic document feeder) cover is completely closed. 

Solution 5:

• Replace or clean the rollers.

Read More

How to fix error C4EB8802 on HP printers

This error appears on these models: Photosmart D110A, C4780, 4683, 4680, etc...


Solution 1:

• Switch on the printer. 
• Disconnect USB cable or lan cable and disconnect the power cable. 
• Wait for 30 seconds. 
• Connect the power cable. 
• Switch on the printer. 

Solution 2:

• If the error persist.
• Disconnect the power cable with the printer powered on.
• Hold on "OK" et  "HELP" buttons while plugging in the power cord.
• Switch on the printer. 

Solution 3:

• Uninstall printer driver and software.
• Disconnect USB cable. 
• Reboot and reconnect the printer. 
• Install the drivers. 

Solution 4: 

• In the firewall: verify that the printer is not blocked.

Solution 5:

• Checked the board for the flex cables.
• If one had come loose, unplugged the printer and re-seated all the cables.

Read More

Error code 5100 on Canon inkjet printers

Solution 1:

• Look inside for a tiny object like a piece of paper, a staple...

Solution 2:

• There is a thin plastic strip running across the width in front of and below the drive belt: there are fine black vertical lines on this strip. 
• If the strip gets a piece of crud on it, you get an error during the start-up sequence.
• Gently clean this strip with a damp lint-free tissue.

Solution 3:

• The purge cap (the white sliding mechanism that the print head parks to when it's not in use) may be not lubricated well enough. 
• Lubricate the sliders with some white grease (don't get it on the small wipers or the black caps).
• This repair probably require to remove the right panel off of the printer to gain access to the purge mechanism.

Read More

Error code 5B00 on Canon IP2700 printer

MAJ 17/10/16

The error code 5B00 means the waste ink counter is full, you need to reset it.


First, search and download the resetter PCM_servicetool (.rar)

Step 1: enter in service mode in order to used the resetter:

• Turn off the printer without pulling the power cords.
• Hold down Resume button and press Power button.
• Keep holding down Power button and let Resume button go.
• Then Press Resume button 5 times then let both buttons go.
• The Alternate Blinking error is gone: the printer is in Service Mode state.

Step 2:

• Extract the resetter and double click "servicetool.exe"
• Click Reload Button and you will get a new USB port.
• Load some papers in your printer and press the "Main" Button, wait until it shows "error 001" then press OK.
• Then press "EEPROM" button and the printer will print some text, after that click OK
• Then power off the printer (sometimes you have to press twice the power button to turn off) and turn on again. 
• That's done.

Troubleshooting:

• Error 005: the printer is not compatible with this service tool
  
• Error 006 with the Service tool: 

After clicking "Maint button" on clear ink counter section the program hang up, wait for e few minutes still the progam not responding.


Link:

• How to solve erreur 5200 or P08 ?

Read More

The printheads for Canon Inkjet printers

MAJ 02/01/15

QY6-0031-000: BJC610 - BJC620
QY6-0034-000: I6300 - I6500 - S500 - S520 - S530D - S600 - S6000 - S630 - S6300 - MPC400 - MPC600F - Multipass: F30 - F50 - S500 - S520 - S530D - S600 - S630 - S6300
QY6-0035-000: BJC8200 - S800
QY6-0037-000: IP1800 - S300 - S330 - MPC190 - MPC200 - Multipass: F20
QY6-0038-000: S200 - S200X
QY6-0039-000: I910 - S900 - S9000
QY6-0040-000: S800 - S820D - S830 - S830D
QY6-0041-000: S70 - S750 - Multipass: F60 - F80
QY6-0043-000: I950 - I960 - I965
QY6-0044-000: I250 - I320 - I350 - IP1000
QY6-0045-000: I550 - I550X
QY6-0046-000: I470D - I70
QY6-0049-000: I860 - I865 - IP4000 - IP4000R - MP750 - MP760 - MP780 - MP770 - MP790
QY6-0050-000: I900 - I950 - IP6000D
QY6-0052-000: I80 - IP90
QY6-0053-000: I990
QY6-0054-000: I450 - I455 - I470D - I475D - IP1500
QY6-0055-000: I9950 - IP8500
QY6-0056-000: DELPHY DS700 - DELPHY DS810
QY6-0057-000: IP5000
QY6-0059-000: IP4200 - MP500 - MP530
QY6-0061-000: IP4300 - IP5200 - IP5200R - MP600 - MP800 - MP830
QY6-0062-000: MP970
QY6-0063-000: IP6600D
QY6-0064-000: I560 - I850 - IP3000 - IP3500 - IX4000 - IX5000 - MP730 - MP700 photo - MP730 photo
QY6-0065: PRO9500
QY6-0068-000: IP100
QY6-0070: IP3300 - IP510 - IP520
QY6-0072: IP4600/MP630
QY6-0073: MP540 - MP620 - MX620 - IP3600
QY6-0074-000: MP980
QY6-0075-000: IP4500 - IP5300 - MP610 - MP810 - MX850
QY6-0077: PRO9500
QY6-0078-000: MP990, MP996
QY6-0080-000: IP4580, MG5250,
QY6-0082: IP7220 MG5420 MG5520 MG6420
QY6-0083-000:
QY6-1000-000: N1000 - N2000

Error code list by brandt

Read More

Error C0420 on Kyocera Mita printers

KM2560, KM5030...

Error C0420  means that the paper deck or feed deck motor is not functioning.

Solution:

• See if the paper tray is fully closed. 
• If so, pull out the tray and replace it.

Read More